Immunoprecipitation of COX IV from HeLa cells using COX IV (3E11) Rabbit mAb #4850 and Protein A Magnetic Beads. Western blot analysis was performed on the 10% input control (lane 1), IP pellet (lane 2) and Rabbit (DAIE) mAb IgG XP® Isotype Control #3900 (at matched concentration) (lane 3) using COX IV (3E11) Rabbit mAb #4850.Learn more about how we get our images
This protocol is intended for immunoprecipitation of native proteins for analysis by western immunoblot or kinase activity utilizing Protein A magnetic separation.
NOTE: Prepare solutions with reverse osmosis deionized (RODI) or equivalent grade water.
10X Cell Lysis Buffer: (#9803) To prepare 10 ml of 1X cell lysis buffer, add 1 ml cell lysis buffer to 9 ml dH2O, mix.
NOTE: Add 1 mM PMSF (#8553) immediately prior to use.
A cell lysate pre-clearing step is highly recommended to reduce non-specific protein binding to the Protein A Magnetic beads. Pre-clear enough lysate for test samples and isotype controls.
IMPORTANT: Pre-wash #73778 magnetic beads just prior to use:
Carefully remove the buffer once the solution is clear. Add 500 μl of 1X cell lysis buffer to the magnetic bead pellet, briefly vortex to wash the beads. Place tube back in magnetic separation rack. Remove buffer once solution is clear. Repeat washing step once more.
IMPORTANT: The optimal lysate concentration will depend on the expression level of the protein of interest. A starting concentration between 250 μg/ml-1.0 mg/ml is recommended.
IMPORTANT: Appropriate isotype controls are highly recommended in order to show specific binding in your primary antibody immunoprecipitation. Use Normal Rabbit IgG #2729 for rabbit polyclonal primary antibodies, Rabbit (DA1E) mAb IgG XP® Isotype Control #3900 for rabbit monoclonal primary antibodies, and Mouse (G3A1) mAb IgG1 Isotype Control #5415 for mouse monoclonal primary antibodies. Isotype controls should be concentration matched and run alongside the primary antibody samples
Proceed to one of the following specific set of steps.
NOTE: To minimize masking caused by denatured IgG heavy chains (~50 kDa), we recommend using Mouse Anti-Rabbit IgG (Light-Chain Specific) (D4W3E) mAb (#45262) or Mouse Anti-Rabbit IgG (Conformation Specific) (L27A9) mAb (#3678) (or HRP conjugate #5127). To minimize masking caused by denatured IgG light chains (~25 kDa), we recommend using Mouse Anti-Rabbit IgG (Conformation Specific) (L27A9) mAb (#3678) (or HRP conjugate #5127).
posted December 2008
revised April 2018
Supplied in PBS, 0.1% BSA, 0.004% EDTA and 0.075% sodium azide. Store at 4°C. This product is stable for 12 months.Do not freeze, dry or centrifuge beads. This may cause irreversible aggregation and decreased binding capacity.
Protein A Magnetic Beads are an affinity matrix for the small-scale isolation of immunocomplexes from immunoprecipitations (IP assays). Protein A is covalently coupled to a magnetic particle.
Protein A exhibits high affinity for subclasses of IgG from many species (including human, rabbit, mouse, rat, and sheep) and can be used for immunoprecipitation assays with these antibodies. Beads can be separated from solution using our 6-Tube Magnetic Separation Rack #7017 or 12-Tube Magnetic Separation Rack #14654, which concentrates the beads to the side of the tube instead of the bottom. This eliminates centrifugation steps, minimizes sample loss, increases washing efficiency, and saves time.
The 1mL and 5mL size is enough material for 25 and 125 immunoprecipitations, respectively, when following our recommended protocol.
Bead Diameter: ~1.5 μm
Binding Capacity: > 0.2 μg Rabbit IgG/μl bead slurry
Cell Signaling Technology is a trademark of Cell Signaling Technology, Inc. XP is a registered trademark of Cell Signaling Technology, Inc.
Discover what’s going on at CST, receive our latest application notes and tips, read our science features, and learn about our products.
|73778L||5 ml (5 x 1ml)||N/A|
To get local purchase information on this product, click here.